Page 1 of 1

Piston rings, O-rings or what?

Posted: Sun Jan 21, 2018 8:12 pm
by steedspeed
So! Best seal for a stirling engine power piston?

Re: Piston rings, O-rings or what?

Posted: Mon Jan 22, 2018 3:37 am
by Ian S C
Best seal is a well fitting piston, no rings, a labyrinth seal on the piston skirt. Another type of seal can be used, that is in the form of a cup seal, either leather or plastic.
This is the piston in my stove top fan, as set up here it has a leather cup seal, an labyrinth seal grooves in the piston skirt. As it turned out the cup seal was not required.
Ian S C
[img]
Test 046.JPG
Test 046.JPG (106.81 KiB) Viewed 8967 times
[/img]

Re: Piston rings, O-rings or what?

Posted: Mon Jan 22, 2018 9:07 am
by Alfista

Rizzo, among others, writes about using o-rings. Cast iron rings can be an excellent choice in larger engines. Pfte is an excellent choice for making rings but may wear more quickly than some other materials. Rings are probably not desirable in smaller sizes.




Re: Piston rings, O-rings or what?

Posted: Mon Jan 22, 2018 12:59 pm
by steedspeed
I'm going with two 4 inch diameter pistons.

rings for a 4" piston

Posted: Mon Jan 22, 2018 2:25 pm
by Alfista
I would suggest a lightweight, aluminum piston with 2 rings per piston, each ring .188" to .25" in width. That way, you can also reduce the diameter of the piston and avoid some friction along the length of the piston. If your cylinder is cast iron, use cast iron rings.


Re: Piston rings, O-rings or what?

Posted: Mon Jan 22, 2018 2:35 pm
by steedspeed
Thanks! BTW, has anyone tried using a rolling diaphragm seal?

Re: Piston rings, O-rings or what?

Posted: Tue Jan 23, 2018 3:45 am
by Ian S C
Have not tried the rollsock, but that way gets rid of the friction of the piston, as this is made a non contact unit. Here is the piston for a 4" Heinrici motor, the top end of the displacer is at the bottom of the photo.
Ian S C


[img]
DSC01195.JPG
DSC01195.JPG (124.55 KiB) Viewed 8945 times
DSC01089 (640x480).jpg
DSC01089 (640x480).jpg (206.02 KiB) Viewed 8946 times
[/img]

Re: Piston rings, O-rings or what?

Posted: Tue Jan 23, 2018 9:29 pm
by steedspeed
I thought about the diaphragm but I want the cold cylinder walls to contact the air as it reaches BDC

Re: Piston rings, O-rings or what?

Posted: Wed Jan 24, 2018 4:53 am
by Ian S C
The cooling system on a diaphragm type engine would be in the area of the diaphragm, about the same area as a piston in a cylinder. I think I'll stick to cast iron pistons in either steel or cast iron cylinders.
Here's the displacer for the little Heinrici motor.
Ian S C
DSC01196 (2).JPG
DSC01196 (2).JPG (131.44 KiB) Viewed 8923 times

Great Photos

Posted: Wed Jan 24, 2018 8:00 am
by Alfista
Great photos Ian ! Thank you for posting those !

Wayne

Re: Piston rings, O-rings or what?

Posted: Wed Jan 24, 2018 10:32 am
by steedspeed
I love those old engines. This will be my first hot air engine. Before that I built a "Masie" live steam engine years ago.

Re: Piston rings, O-rings or what?

Posted: Thu Jan 25, 2018 4:55 am
by Ian S C
I'd love to get one of those of my own, that one belongs to a friend who lives a bout a hundred metres down the street.
Just looking at the displacer, its about 3.5 x its diameter long, the usual quote on length is 3 : 1, but a little longer is no problem, I think some of mine have gone to 4 : 1.
Ian S C